• Join over 1.2 million students every month
  • Accelerate your learning by 29%
  • Unlimited access from just £6.99 per month

Aim: To determine the conecentrations of hychloric acid and ethanoic acis by thermometric titration and find the enthalpy of neutralization.

Extracts from this document...

Introduction

Experiment 12 ~ A thermometric titration ~ Lab Report Shek Pok Man, Dominic (6B 24) Aim: To determine the conecentrations of hychloric acid and ethanoic acis by thermometric titration and find the enthalpy of neutralization. Procedure: (I) Titration of HCL with standard NaOH: 1. 50cm3 of NaOH solution is pipetted and transfer to the polystyrene cup, It was allow to stand for a few minutes. 2. The initial temperature was recorded. 5.0 cm3 ofHCL was burette to the cup. 3. The mixture was stirred well by using the thermometer, the temperature was recorded. 4. Sucessive 5.0 cm3 portions of HCL was added and the mixture was stirred, the temperature was recorded after each addition. 5. The adding and recording process was continued till the addition of 50 cm3 of acid. (II) Titration of CH3COOH with standard NaOH: 1. The procedure was the same as HCL except CH3COOH was used. Results and Calculations: (I) ...read more.

Middle

2NaCl + H2O As NaOH is limited reagent, ? no. of mole of H2O = (1)(50/1000) = 0.05 mol ?Honeu = 2926/0.05 ?Honeu = ? 58.52 kJ (Calculations) CH3COOH + NaOH ? CH3COOH-Na+ + H2O As NaOH is limited reagent, ? no. of mole of H2O = (1)(50/1000) = 0.05 mol ?Honeu = 627/0.05 ?Honeu = ? 12.54 kJ ?The standard enthaply change of neutralization of using HCl and CH3COOH are ?58.52kJ mol-1 and ?12.54kJ mol-1 respectively. Questions: 1. [H2O] is a constant when it acts as a solvent. The equilibrium will shifts to the left or shift to the right and [H2O] remanins unchanged. As the [acid] and [base] is very low though it is strong, [H2O] remanins unchanged. 2. (I) Some heat is lost to the surrounding. (II) We assume that the heat capacity of the cup is zero. ...read more.

Conclusion

(discussion) We should try hard to make sure whether the rise in temperature is logical, if the temperature have no willing to increase for a degree after a few times of the addition of the strong acid. We should once report it to the teacher to find if the given reagent has a different concentration from given. As sodium hydroxide is very corrosive, we must use the pipette filler supplied, and we must wear lab coat and safety spectacles in the laboratory. The last drop of the pipette should be dipped into the solution. We should fill the burette with a filter funnel and under eye sight for safety reasons. The filter funnel should be removed after filling. The burette should be placed upright to the vertical. Conclusion: The value from experimential result of neutralizatin using HCl and CH3COOH are ?58.52kJ mol-1 and ?12.54kJ mol-1 respectively. The one using HCl is more negative than ?57.6 kJ mol-1 , as the maximum temperture attained may be higher estimated. ?? ?? ?? ?? 1 ...read more.

The above preview is unformatted text

This student written piece of work is one of many that can be found in our AS and A Level Physical Chemistry section.

Found what you're looking for?

  • Start learning 29% faster today
  • 150,000+ documents available
  • Just £6.99 a month

Not the one? Search for your essay title...
  • Join over 1.2 million students every month
  • Accelerate your learning by 29%
  • Unlimited access from just £6.99 per month

See related essaysSee related essays

Related AS and A Level Physical Chemistry essays

  1. Marked by a teacher

    Heat of Neutralization. Objective: To investigate the ...

    5 star(s)

    2. The content in the polystyrene foam cup was let equilibrate for a few minutes and the temperature of the solution was measured and the result was recorded. 3. The acid was poured into the burette to the mark '0 cm' through a filter funnel and make sure the tip of burette was drained before taking reading.

  2. Heat of Neutralization

    Polystyrene foam is a good insulator, even though some heat would be absorbed by the cups and some would be released to the surroundings, it is small enough as compared to the heat absorbed by the solution in the calorimeter.

  1. Determination of the content of Mg (OH)2 in an indigestion remedy by back titration ...

    In hindsight it would have more appropriate to do a complexometric titration instead of the back titration as there is a mixture of metal ions (sodium & magnesium) present in the "Milk of Magnesia" mixture and would have given a more accurate result to calculate if the %w/w of the sample tested complied with values stated in the B.P.

  2. Drug: Antacid Effectiveness Analysis To determine the neutralizing ability of antacids in different ...

    This is predicted by Le Chatelier's principle. Hypothesis Our hypothesis is the greater proportion of the active ingredient with stronger base in an antacid tablet will have the greater neutralizing power. And thus, it will be more effective to cure upset stomach. Information of three types of antacid tablets 1.

  1. Free essay

    Determining an Equilibrium constant

    Mass of water in HCl(aq) /g 4.796 4.716 4.856 4.826 4.766 4.606 9. Initial amount of water /mol 0.2664 0.2620 0.3281 0.3210 0.4314 0.4220 10. Eqm. amount of water /mol 0.2503 0.2450 0.3147 0.3082 0.4201 0.4084 11. Eqm. constant, Kc 0.0292 0.0342 0.02 0.0188 0.0317 0.065 12 Mean Value of Kc Calculation :( Set 2a)

  2. Lab Report. Objective: To determine the concentration of unknown standard sodium hydroxide solution ...

    of HNO3(aq) (?) 25.2 25.2 24.9 25.0 24.8 24.7 24.6 Initial temp. of NaOH(aq) (?) 25.2 24.9 24.7 25.1 24.8 24.8 25.1 Final temp. of mixture (?) 26.3 27.4 28.9 30.6 28.8 27.1 26.3 Initial temp. of mixture (?) 25.2 25.1 24.8 25.1 24.8 24.8 25.0 Temperature change (?)

  1. Investigating the Rate of the Reaction between Bromide and Bromate Ions in Acid Solution

    + H+(aq) --> HBr(aq) (Equation 3.8.3) Step 2 (fast): BrO3-(aq) + H+(aq) --> HBrO3 (aq) (Equation 3.8.4) These two products, hydrogen bromide and hydrogen bromate, then react together in the rate determining step: Step 3 (slow): HBr(aq) + HBrO3 (aq)

  2. Investigating how concentration affects rate of reaction

    I investigated suitable concentrations of each solution to use. I noticed that at much lower concentrations, the reaction went much too slowly. If the reaction goes too slowly I would not have time to do five repeats for each concentration. This would reduce both accuracy and reliability of my results.

  • Over 160,000 pieces
    of student written work
  • Annotated by
    experienced teachers
  • Ideas and feedback to
    improve your own work