• Join over 1.2 million students every month
  • Accelerate your learning by 29%
  • Unlimited access from just £6.99 per month

Chemistry polymers.

Extracts from this document...

Introduction

Emmanuel Ntombura 18/09/2003 CHEMISTRY - POLYMERS The crude oil fraction that polymers go into is the naphtha fraction. This fraction normally contains Alkanes. Ethene put under pressure and heated with a catalyst will polymerise to form poly (ethene). Note that there are no double bonds in the polymer. Poly (ethene) is an alkane. It is a saturated hydrocarbon. This process is called polymerisation. A polymer that is formed from monomers added together where no substance (other than the polymer) is produced is called an addition polymer. Examples of addition polymers are poly (ethene), poly (propene), poly (chloroethene) - PVC, and poly (phenylethene) - poly (styrene). The double bond in an alkene (like ethene) can be broken open and joined to other molecules. A molecule of ethene can be joined to another molecule of ethene. In the process, the second ethene molecule has its double bond broken, and this may be added to a third molecule of ethene, and so on. ...read more.

Middle

The same polymer can be reheated and remoulded. Such polymers are called thermosoftening (meaning that they go soft when you heat them). Some polymers do not form crystals. This is because the molecules become bonded to each other so they won't break and there are strong covalent bonds, which cannot be broken. They also soften when heated and harden when cooled down again. When cold, they are not crystalline but glassy. These polymers are called Thermosets or Thermosetting plastics. Polymers may be classified as thermosoftening or thermosetting. Thermosetting polymers have their chains cross-linked by covalent bonds. The polymer is originally placed into a mould to form the desired shape. The polymer is then heated and chemical reactions occur to form the cross links between the chains. The resulting three-dimensional solid structure cannot then be changed. Further heating will not cause the polymer to soften or change shape (unlike thermosoftening polymers). Examples of thermosetting polymers are: 1. Melamine - used in furniture. 2. ...read more.

Conclusion

are biodegradable. When buried, bacteria and fungi break them down into useful nutrients for further plant growth. Nature recycles its own products. Polymers produce toxic materials (poisons) when burnt, in addition to the expected products from combustion of a hydrocarbon, which are carbon dioxide, water, carbon monoxide and carbon (soot). Those that contain chlorine (PVC for example) also produce hydrogen chloride on burning. Those that contain nitrogen (nylon for example) produce hydrogen cyanide. Polymers are a fire hazard. Many people die from the smoke of burning polymers in house fires, long before the fire reaches them. Burning polymers is not a good way of disposing of them. Solutions More and more polymers are being recycled. This is not as cost effective as recycling metals, but we don't want to live amongst piles of (unrotting) plastic. Research into biodegradable polymers will increasingly provide useful replacements for the main polymers of today. Another solution is mechanical recycling. This is where you return the polymers to small chains again under high heat and pressure in the absence of oxygen. 1 ...read more.

The above preview is unformatted text

This student written piece of work is one of many that can be found in our GCSE Resistant Materials section.

Found what you're looking for?

  • Start learning 29% faster today
  • 150,000+ documents available
  • Just £6.99 a month

Not the one? Search for your essay title...
  • Join over 1.2 million students every month
  • Accelerate your learning by 29%
  • Unlimited access from just £6.99 per month

See related essaysSee related essays

Related GCSE Resistant Materials essays

  1. EFFECT OF MOISTURE ON THE MECHANICAL PROPERTIES OF NYLON

    of extracted polycaprolactam, new to the American but not the European market, the number of United States manufacturer gradually grew. The susceptibility of Nylon to modification was clear from the outset. Different acids and amines could be reacted to provide a variety of Nylons and Nylon copolymers.

  2. THE BENEFITS OF RECYCLING

    In 2002, recycling reduced greenhouse gas emissions by 2 million metric tons of carbon equivalent, comparable to taking 1.3 million passenger cars off Pennsylvania's roads. Recycling Reduces Emissions of Air and Water Pollutants In addition to greenhouse gases, recycling can reduce a range of pollutants from entering the air and water.

  1. Supply Chain Management

    In this phase of development, capacity of the manufacturing process is assumed to be infinite for the purposes of calculations. The material is planned according to the forecast timing, with no regard to the actual capacity. Manufacturing Resource Planning is the next evolution of the MRP methodology, which includes manufacturing routings and work centre capacities.

  2. Describe the layout and furniture of aTypical Athenian house.

    The women's quarters or Gynaikon were usually nearer the back of the house so that the man of the house could tell if she was trying to sneak out. In the women's quarters you would find a bedroom for them and a room for spinning and weaving materials and clothes.

  1. Analysis of Existing Products.

    This closed bookshelf would easily fit into the environment of Bangkok as they are made out of wood. Wood is a material, which can withstand the heat and therefore wouldn't be damaged by the sun's rays. Also the closed bookshelf has adjustable shelves which means that every type of book can fit into the shelf.

  2. Six sigma methology for solving automotive engineering problems.

    The tool used for deciding in the set of experiments, fitting the regression equations and optimizing is MINITAB [1]. 3. Case studies 3.1 Optimization of Lift Mechanism 3.1.1 Problem Definition Figures 2a, 2b and 2c show three configurations a typical front seat needs to provide for an occupant.

  1. Carbon Fibre chemistry assignment.

    The resultant is almost 100% Carbon. The temperature the fibres are heated to will determine the quality of the resultant fibres. There are four grades of carbon fibre. These are as follows: GRADE Temperature HeatedTo (�C) Modulus of Elasticity (Gpa) Low Modulus To 1000 To 200 Standard Modulus 1000 to 1500 200 to 250 Intermediate Modulus

  2. My aim of this experiment is to recognize which material is the greatest sound ...

    for my results, by carrying this whole process out three times, and then produce an average results table from which I would then produce a graph out of and distinguish which material is the best sound insulator. I would repeat the process and measure the sound values until I have

  • Over 160,000 pieces
    of student written work
  • Annotated by
    experienced teachers
  • Ideas and feedback to
    improve your own work